Crown Molding Installation

1.Cut the Corners of the Molding
The hardest part of installing crown molding is cutting the corners. You can’t do it like any other trim pieces because the molding sits at an angle between the wall and the ceiling . Using a coping saw is the easiest way to cut the corners because a coped joint is tighter than a mitered joint. A coping saw is also good for a beginner. Any gap in a coped cut can be easily concealed with a little bit of caulk.

Another tool that will make the job easier is a power miter saw . It’s accurate and makes a cleaner cut than a plastic miter box.

2.Measure and Mark the Wall
Measure the wall for the length of your first piece of molding. Mark the wall to show the bottom edge of the molding.

3.Cut the First Measured Piece
Once you determine the length, take the molding to the saw and cut in a straight line at a 90-degree angle — you want both ends of the molding to butt against the side walls.

4.Cut the Next Piece to Fit an Inside Corner
Move the miter saw guide to the 45-degree angle point and set the molding into place. The edges need to be pressed firmly against the saw table and the vertical side fence. This is the first key to a straight cut and a good fit.

5.Understand How the Pieces Fit Together
The second key is not so obvious and can be a bit confusing. The molding is upside down, meaning the edge against the vertical fence is the bottom of the molding and the edge against the table is the top of the molding (think of your table as the ceiling).

6.Cut the Molding at a 45-Degree Angle
With the molding in the proper position, use a 10-inch saw blade to cut a perfect 45-degree angle. It is also important here to make sure you cut the molding angle in the right direction: for an inside corner, the bottom of the molding should be longer than the top part of the molding; for an outside corner, the top of the molding will be longer than the bottom.

7.Cope the Joint
When you cope a joint, you scribe the end of one molding to the face of the other. Darken the front edge with a pencil and then use the coping saw to cut as close to the line as you can. You need to hold your thumb against the side of the blade to guide the start of your cut. Start slowly, so you don’t splinter the delicate edge. Cut at a slight angle. You want to cut off more from the edge of the molding and you don’t need to cut it all at one time. Cut out small pieces to make creating this coped joint easier.

8.Check the Fit
Check the fit against a scrap piece of molding to reveal any gaps that need to be trimmed. Use the coping saw to cut off the high points. 9.Attach the Molding to the Wall

Once the fit is right, take the molding to the wall. For a long piece, you’ll need some help holding it. Push the end into the corner, making the fit as tight as possible; attach it to the wall. Use the caulk gun to cover up any gaps in the joint (make sure you’re using paintable caulk). You may need another small piece of molding to finish out the wall. 10.Make Miter Cuts for the Outside Corners
The outside corners should meet exactly (a caulk gun can’t help you much here). Less experienced DIYers may want to paint the crown molding, since paint and caulking can be used to hide any small mistakes — with stained molding, it’s much harder to disguise imperfections. 11.Use Optional Corner Blocks
You can skip the miter and coping cuts altogether by using corner blocks, which will prevent having to cut angles into the molding. It looks professional and tends to be a lot easier.

The New Fuss About Crown Molding Installation

The Hidden Truth About Crown Molding Installation

Just like any undertaking, there is an assortment of approaches to cut and install crown molding and in case you have a different method which you are comfortable with, then by all means use it. It can be used to make a dramatic and elegant statement. It can add a finishing touch to any room in your home. It is a type of trim and is often installed in tandem with baseboards, chair rails and other decorative finishes that give your new home, office or remodel a polished look. Often, it will not reach the entire length of a wall. Most crown molding has to be miter cut prior to installation and demands specialized sorts of cuts which are beyond the ability of the majority of novices.

The Foolproof Crown Molding Installation Strategy

Installation is pretty straightforward. Professional installation is nearly always required, as a result of difficulty of working with plaster molding generally speaking. Molding installation may be an easy and Affordable method to `punch-up’ the appearance of a room. Crown molding installation demands advanced, experienced carpentry abilities. Superior crown molding installation is important for your woodwork to appear natural and not only like you nailed a couple of boards around the outside of your room.

The Importance of Crown Molding Installation

When it has to do with cutting crown molding, we need to be meticulous. Crown molding may be used to improve any room in your home. It is an excellent home improvement project because it creates a classic, elegant accent wherever you decide to install it. Crown moldings can transform a normal room into an elegant and distinctive space that you’re going to be content to devote time in and use to entertain your friends and loved ones. If you’re trying to install crown molding we are a great selection of company as we have experience and understanding of instillation. Crown molding doesn’t always have to get installed against both the wall and the ceiling. Fitting crown molding demands a cut at the right blend of miter angle and bevel angle.

The crown molding must be cautiously measured and crafted to fit each particular room. With the Crown45, crown molding is going to be cut the direction you see and install it to the wall. It is the name for the wood that runs along the top of your woods horizontally, and it is commonly used to conceal the transitions where your ceiling and walls connect, as well as adding to the appearance of the room. It is easy, and the pre made corners make it even easier. Needless to say, hand-milled crown molding is still an alternative, but it’s often cost-prohibitive for the typical homeowner. Installing crown molding is a good means to add elegance in a house. It is one of the best ways to add instant value to your home.

Adding molding might seem like a little difference but it makes your home your own in addition to improving the appearance. It is as simple as crown molding gets! Similarly, it is favored because of the usability and the additional depth it adds to the room. There isn’t anything like crown molding to bring some elegance to internal rooms and halls.